4 Sep
2008
4 Sep
'08
11:15 a.m.
Bueno, con el Wifi-scanner veo las redes, no asigna la ip automáticamente,
le meto la ip desde el wifi escaner, en el ifconfig me sale pero no
navega... (algo es algo!)
Lo raro es que me sale la "wlan0" y mas abajo "wlan0_remove" o algo
así (no
tengo el portátil delante) ...
salU2
----- Original Message -----
From: "Rafael Toucedo" <rtoucedo(a)gmail.com>
To: "Lista pública de GALPon - Grupo de Amigos de Linux de Pontevedra"
<galpon(a)listas.galpon.org>
Sent: Thursday, September 04, 2008 12:06 AM
Subject: Re: [GALPon] Una de Debian
debian:/home/rafa# iwconfig
lo no wireless extensions.
eth1 no wireless extensions.
wmaster0_rename no wireless extensions.
wlan0 IEEE 802.11 ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=0 dBm
Retry min limit:7 RTS thr:off Fragment thr=2352 B
Encryption key:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
debian:/home/rafa#
bueno, ya tengo el dispositivo com wlan0,
ahora no resuelve el dhcp ni de coña
debian:/home/rafa# ifconfig
eth1 Link encap:Ethernet HWaddr 00:1a:80:20:fc:07
inet addr:192.168.1.103 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::21a:80ff:fe20:fc07/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1016 errors:0 dropped:0 overruns:0 frame:0
TX packets:901 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1007524 (983.9 KiB) TX bytes:203752 (198.9 KiB)
Interrupt:16
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:119 errors:0 dropped:0 overruns:0 frame:0
TX packets:119 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:31789 (31.0 KiB) TX bytes:31789 (31.0 KiB)
wlan0 Link encap:Ethernet HWaddr 00:1b:77:ed:3b:6f
inet6 addr: fe80::21b:77ff:feed:3b6f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:47 errors:0 dropped:0 overruns:0 frame:0
TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:11409 (11.1 KiB) TX bytes:3296 (3.2 KiB)
wmaster0_rename Link encap:UNSPEC HWaddr
00-1B-77-ED-3B-6F-77-6C-00-00-00-00-00-00-00-00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
en fin ¿no habrá alguna herramienta gráfica (gnome a poder ser) que me
ayude a configurar esto?
muchas gracias por todo !
2008/9/3 Jorge R. <jrrperi(a)gmail.com>om>:
Bueno parece que por lo menos ya estás asociado :P .
Por lo de udev prueba lo siguiente :
# This file was automatically generated by the /lib/udev/write_net_rules
# program, probably run by the persistent-net-generator.rules rules file.
#
# You can modify it, as long as you keep each rule on a single line.
# MAC addresses must be written in lowercase.
# Firewire device 08004603027dc1a6 (ohci1394)
SUBSYSTEM=="net", DRIVERS=="?*",
ATTRS{address}=="08:00:46:03:02:7d:c1:a6",
NAME="eth0"
# PCI device 0x11ab:0x4351 (sky2)
SUBSYSTEM=="net", DRIVERS=="?*",
ATTRS{address}=="00:1a:80:20:fc:07",
NAME="eth1"
# PCI device 0x8086:0x4222 (ipw3945)
SUBSYSTEM=="net", ACTION=="add", DRIVER=="?*",
ATTRS{address}=="00:1b:77:ed:3b:6f", NAME="wlan0"
A ver si traga ! , suerte .
2008/9/3 Rafael Toucedo <rtoucedo(a)gmail.com>
--
Rafael Toucedo.
con un ifconfig... (no tengo ip será por q estoy usando eth0? (el cable)
wlan0_rename Link encap:Ethernet HWaddr 00:1b:77:ed:3b:6f
inet6 addr: fe80::21b:77ff:feed:3b6f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:29 errors:0 dropped:0 overruns:0 frame:0
TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:8090 (7.9 KiB) TX bytes:3296 (3.2 KiB)
debian:/home/rafa# iwconfig
lo no wireless extensions.
eth1 no wireless extensions.
eth2 no wireless extensions.
wlan0_rename IEEE 802.11 ESSID:"nat_net"
Mode:Managed Frequency:2.437 GHz Access Point:
00:1C:10:0B:52:29
Bit Rate=54 Mb/s Tx-Power=15 dBm
Retry min limit:7 RTS thr:off Fragment thr=2352 B
Encryption key:AEAE-1212-AE
Link Quality=97/100 Signal level=-28 dBm Noise level=-127 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
debian:/home/rafa#
en las reglas de persistencia hay algo curioso:
debian:/etc/udev/rules.d# vi 70-persistent-net.rules
# This file was automatically generated by the /lib/udev/write_net_rules
# program, probably run by the persistent-net-generator.rules rules file.
#
# You can modify it, as long as you keep each rule on a single line.
# MAC addresses must be written in lowercase.
# Firewire device 08004603027dc1a6 (ohci1394)
SUBSYSTEM=="net", DRIVERS=="?*",
ATTRS{address}=="08:00:46:03:02:7d:c1:a6", NAME="eth0"
# PCI device 0x11ab:0x4351 (sky2)
SUBSYSTEM=="net", DRIVERS=="?*",
ATTRS{address}=="00:1a:80:20:fc:07",
NAME="eth1"
# PCI device 0x8086:0x4222 (ipw3945)
SUBSYSTEM=="net", DRIVERS=="?*",
ATTRS{address}=="00:1b:77:ed:3b:6f",
NAME="eth2"
si te dijas pone "ETH2" y el "device" es ipw3945... ¿por qué
entonces
es wlan0 en mi pc?
me estoy liando...
gracias !
2008/9/3 Jorge R. <jrrperi(a)gmail.com>om>:
_______________________________________________
GALPon mailing list
GALPon(a)listas.galpon.org
https://listas.galpon.org/cgi-bin/mailman/listinfo/galpon
El 3 de septiembre de 2008 22:45, Rafa Toucedo <rtoucedo(a)gmail.com>
escribió:
--
Rafael Toucedo.
_______________________________________________
GALPon mailing list
GALPon(a)listas.galpon.org
https://listas.galpon.org/cgi-bin/mailman/listinfo/galpon
Jorge R. escribió:
> ¿Aparece algún interfaz al hacer iwconfig ?
debian:/home/rafa# iwconfig
lo no wireless extensions.
eth1 no wireless extensions.
eth2 no wireless extensions.
wlan0_rename IEEE 802.11 ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point:
Not-Associated
Tx-Power=0 dBm
Retry min limit:7 RTS thr:off Fragment thr=2352 B
Encryption key:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Lo del nombre de wlan0_rename es cosa de udev , prueba a bajar , subir
la
interfaz y asociarte (ifconfig wlan0_rename down && iwconfig
wlan0_rename
mode managed && ifconfig wlan0_rename up && iwconfig wlan0_rename essid
<tuessid> key <tukey> ) ( Para cambiar el modo de la interfaz tienes
que
bajarla antes )
Para lo de udev , tendras que buscar en /etc/udev/rules.d/ y editar el
fichero de las reglas de persistencia.
Espero que te sirva de ayuda. Un saludo
_______________________________________________
GALPon mailing list
GALPon(a)listas.galpon.org
https://listas.galpon.org/cgi-bin/mailman/listinfo/galpon